Torque Charts - Hydraulic & Pneumatic

 

TJ Tools are equipped to carry out Torque Calibration to Hand Multipliers, Hydraulic and pneumatic Torque tools. Over 20 years experience performing torque calibration. NATA traceable certificates are provided along with tool condition assessments.

RAD Photos

Torque Charts - Hydraulic & Pneumatic

TJ Tools offer Torque Charts with the following considerations. The Charts are readings we have taken from tool models during service work. It should be noted, all tools vary slightly depending on age, brand, condition etc. We accept no responsibility for any typos or readings. We recommend you contact us to obtain re- calibration of your tool - We have available tools for hire at discounted rates while your tool is off site.

 

Rapidtorc Hydraulic Torque Wrench Conversion Charts
RT - Square Drive Wrenches RTX - Hex Cassette Wrenches
Hydraulic Square Drive RTX
RT-1 Hydraulic Wrench 3/4" Drive ( 200 - 1,390 Ft Lbs ) RTX -2 Hydraulic Hex Cassette ( 255 - 1710 ) Ft Lbs
RT-3 Hydraulic Wrench 1" Drive ( 480 - 3,230 Ft Lbs ) RTX -4 Hydraulic Hex Cassette ( 580 - 3855 ) Ft Lbs
RT-5 Hydraulic Wrench 1-1/2" Drv ( 835 - 5590 Ft Lbs ) RTX -8 Hydraulic Hex Cassette ( 1143 - 8151 ) Ft Lbs
RT-8 Hydraulic Wrench 1-1/2" Drv ( 1200-8000 Ft Lbs ) RTX -14 Hydraulic Hex Cassette ( 2010 - 13400 ) Ft Lbs
RT-10 Hyd Wrench 1-1/2" Drv ( 1755 - 11520 Ft Lbs ) RTX -18 Hydraulic Hex Cassette ( 2676 - 17845 ) Ft Lbs
RT-25 Hyd Wrench 2-1/2" Drv ( 3960 - 25890 Ft Lbs ) RTX -30 Hydraulic Hex Cassette ( 4770 - 31800 ) Ft Lbs

 

RAD - Torque Charts

rad

Pneumatic / Air Driven Single speed Tools Ft Lbs

RAD 350 Pneumatic 3/4" Drive - Single Speed Torque Chart
RAD 700 Pneumatic 3/4" Drive - Single Speed Torque Chart
RAD 1000 Pneumatic 3/4" Drive - Single Speed Torque Chart
RAD 1400 Pneumatic 1" Drive - Single Speed Torque Chart
RAD 2000 Pneumatic 1" Drive - Single Speed Torque Chart
RAD 2500 Pneumatic 1" Drive - Single Speed Torque Chart
RAD 3400 Pneumatic 1" Drive - Single Speed Torque Chart
RAD 5000 Pneumatic 1-1/2" Drive - Single Speed Torque Chart
Note: Manufactures indicative chart - Air tools require in individual calibration



Imperial To Metric - Conversion
This Table in a pdf copy
Dec. Imperial mm Dec. Imperial mm

 

 

 

 

 

 

 

 Dec. Imperial mm
0.063   1/16 1.6 3.000 3      76.2 6.000 6      152.4
0.125   1/8 3.2 3.063 3  1/16 77.8 6.063 6  1/16 154.0
0.188   3/16 4.8 3.125 3  1/8 79.4 6.125 6  1/8 155.6
0.250   1/4 6.4 3.188 3  3/16 81.0 6.188 6  3/16 157.2
0.313   5/16 7.9 3.250 3  1/4 82.6 6.250 6  1/4 158.8
0.375   3/8 9.5 3.313 3  5/16 84.1 6.313 6  5/16 160.3
0.438   7/16 11.1 3.375 3  3/8 85.7 6.375 6  3/8 161.9
0.500   1/2 12.7 3.438 3  7/16 87.3 6.438 6  7/16 163.5
0.563   9/16 14.3 3.500 3  1/2 88.9 6.500 6  1/2 165.1
0.625   5/8 15.9 3.563 3  9/16 90.5 6.563 6  9/16 166.7
0.688  11/16 17.5 3.625 3  5/8 92.1 6.625 6  5/8 168.3
0.750   3/4 19.1 3.688 3 11/16 93.7 6.688 6 11/16 169.9
0.813  13/16 20.6 3.750 3  3/4 95.3 6.750 6  3/4 171.5
0.875   7/8 22.2 3.813 3 13/16 96.8 6.813 6 13/16 173.0
0.938  15/16 23.8 3.875 3  7/8 98.4 6.875 6  7/8 174.6
1.000 1      25.4 3.938 3 15/16 100.0 6.938 6 15/16 176.2
1.063 1  1/16 27.0 4.000 4      101.6 7.000 7      177.8
1.125 1  1/8 28.6 4.063 4  1/16 103.2 7.063 7  1/16 179.4
1.188 1  3/16 30.2 4.125 4  1/8 104.8 7.125 7  1/8 181.0
1.250 1  1/4 31.8 4.188 4  3/16 106.4 7.188 7  3/16 182.6
1.313 1  5/16 33.3 4.250 4  1/4 108.0 7.250 7  1/4 184.2
1.375 1  3/8 34.9 4.313 4  5/16 109.5 7.313 7  5/16 185.7
1.438 1  7/16 36.5 4.375 4  3/8 111.1 7.375 7  3/8 187.3
1.500 1  1/2 38.1 4.438 4  7/16 112.7 7.438 7  7/16 188.9
1.563 1  9/16 39.7 4.500 4  1/2 114.3 7.500 7  1/2 190.5
1.625 1  5/8 41.3 4.563 4  9/16 115.9 7.563 7  9/16 192.1
1.688 1 11/16 42.9 4.625 4  5/8 117.5 7.625 7  5/8 193.7
1.750 1  3/4 44.5 4.688 4 11/16 119.1 7.688 7 11/16 195.3
1.813 1 13/16 46.0 4.750 4  3/4 120.7 7.750 7  3/4 196.9
1.875 1  7/8 47.6 4.813 4 13/16 122.2 7.813 7 13/16 198.4
1.938 1 15/16 49.2 4.875 4  7/8 123.8 7.875 7  7/8 200.0
2.000 2      50.8 4.938 4 15/16 125.4 7.938 7 15/16 201.6
2.063 2  1/16 52.4 5.000 5      127.0 8.000 8      203.2
2.125 2  1/8 54.0 5.063 5  1/16 128.6  
2.188 2  3/16 55.6 5.125 5  1/8 130.2
2.250 2  1/4 57.2 5.188 5  3/16 131.8
2.313 2  5/16 58.7 5.250 5  1/4 133.4
2.375 2  3/8 60.3 5.313 5  5/16 134.9
2.438 2  7/16 61.9 5.375 5  3/8 136.5
2.500 2  1/2 63.5 5.438 5  7/16 138.1
2.563 2  9/16 65.1 5.500 5  1/2 139.7
2.625 2  5/8 66.7 5.563 5  9/16 141.3
2.688 2 11/16 68.3 5.625 5  5/8 142.9
2.750 2  3/4 69.9 5.688 5 11/16 144.5
2.813 2 13/16 71.4 5.750 5  3/4 146.1
2.875 2  7/8 73.0 5.813 5 13/16 147.6
2.938 2 15/16 74.6 5.875 5  7/8 149.2
5.938 5 15/16 150.8

 

 

 

 

 

 



Go to Top of This Page